Availability: | |
---|---|
Quantity: | |
LED TV Panel
Prowalls
LED Screen
Description
LED TV Panel is a softlight luminaire featuring Cool White and Warm White LEDs, removable barn doors, linear white color temperature range (3,200K - 5,800K), smooth 16bit dimming curve mode effects, adjustable LED refresh frequency and gamma brightness for flicker free operation for TV and FILM, dimmer control dials.
Features
*Dynamic White 115°Beam TVL Panel SoftLight
*Linear White Color Temp Range (3,200K - 5,800K)
*Smooth 16bit Dimming Curve Mode Effects
*Linear Dimmer and Color Temperature Rotary Control Dials
*Adjustable / Removable Barn Doors Included
*Flicker Free Operation for TV and FILM
Description
LED TV Panel is a softlight luminaire featuring Cool White and Warm White LEDs, removable barn doors, linear white color temperature range (3,200K - 5,800K), smooth 16bit dimming curve mode effects, adjustable LED refresh frequency and gamma brightness for flicker free operation for TV and FILM, dimmer control dials.
Features
*Dynamic White 115°Beam TVL Panel SoftLight
*Linear White Color Temp Range (3,200K - 5,800K)
*Smooth 16bit Dimming Curve Mode Effects
*Linear Dimmer and Color Temperature Rotary Control Dials
*Adjustable / Removable Barn Doors Included
*Flicker Free Operation for TV and FILM
Specification
SOURCE
LED 200W
Dynamic White 115°Beam TVL Panel SoftLight
Linear White Color Temp Range (3,200K - 5,800K)
60,000 Hours LED Lifetime (May vary depending on different factors)
FUNCTION
Dynamic White 115°Beam TVL Panel SoftLight
Linear White Color Temp Range (3,200K - 5,800K)
Smooth 16bit Dimming Curve Mode Effects
Linear Dimmer and Color Temperature Rotary Control Dials
Adjustable / Removable Barn Doors Included
Flicker Free Operation for TV and FILM
Electronic Strobe and Variable Dimming Curve Modes
CONTROL & CONNECTIONS
(2) DMX Channel Modes (4/8 channels)
LCD Display
3-pin DMX In/Out
PowerCON Power In/Out
DMX512, Auto run, Sound, Master/Slave
THERMAL & ELECTRICAL
160W max Power Consumption
Input voltage: 100-240V AC/50-60 Hz
APPROVALS / RATINGS
CE | RoHs Compliant | IP20
SIZE / WEIGHT
21.6" (550mm) Length
11.4" (290mm) Width
5.9" (150mm) Height
17.6lbs (8g) Weight
Specification
SOURCE
LED 200W
Dynamic White 115°Beam TVL Panel SoftLight
Linear White Color Temp Range (3,200K - 5,800K)
60,000 Hours LED Lifetime (May vary depending on different factors)
FUNCTION
Dynamic White 115°Beam TVL Panel SoftLight
Linear White Color Temp Range (3,200K - 5,800K)
Smooth 16bit Dimming Curve Mode Effects
Linear Dimmer and Color Temperature Rotary Control Dials
Adjustable / Removable Barn Doors Included
Flicker Free Operation for TV and FILM
Electronic Strobe and Variable Dimming Curve Modes
CONTROL & CONNECTIONS
(2) DMX Channel Modes (4/8 channels)
LCD Display
3-pin DMX In/Out
PowerCON Power In/Out
DMX512, Auto run, Sound, Master/Slave
THERMAL & ELECTRICAL
160W max Power Consumption
Input voltage: 100-240V AC/50-60 Hz
APPROVALS / RATINGS
CE | RoHs Compliant | IP20
SIZE / WEIGHT
21.6" (550mm) Length
11.4" (290mm) Width
5.9" (150mm) Height
17.6lbs (8g) Weight
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.
Multi-light working in the same time When using controller to control multi lights to work in strobe, the controller just send the channel data . The strobe effect will be depend on each light itself . And please take attention for the follow situation: 1. There will be many situations make the lights are not synchronization in the beginning. (For example: the different time of opening the light , or different time of them connect to the controller) .In this case, you can change value of the controller( for example push 20 to 0, and back to 20), then it can be synchronization. 2. Due to crystal frequency of different lights are not the same exactly, so it may not be synchronization after long time. 3. If need to keep synchronization for long time, there are two ways to do so: A. Using the controller to edit program make the strobe, auto run effect,then they must be synchronization. B. Using the Maser/Slave model
If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore it is essential that the device be earthed. The electric connection must carry out by qualified person. The device shall only be used with rate voltage and frequency. Make sure that the available voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don't project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.
Multi-light working in the same time When using controller to control multi lights to work in strobe, the controller just send the channel data . The strobe effect will be depend on each light itself . And please take attention for the follow situation: 1. There will be many situations make the lights are not synchronization in the beginning. (For example: the different time of opening the light , or different time of them connect to the controller) .In this case, you can change value of the controller( for example push 20 to 0, and back to 20), then it can be synchronization. 2. Due to crystal frequency of different lights are not the same exactly, so it may not be synchronization after long time. 3. If need to keep synchronization for long time, there are two ways to do so: A. Using the controller to edit program make the strobe, auto run effect,then they must be synchronization. B. Using the Maser/Slave model
If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore it is essential that the device be earthed. The electric connection must carry out by qualified person. The device shall only be used with rate voltage and frequency. Make sure that the available voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don't project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.