Specification

SOURCE

Osram R18 380W lamp

580,000 lux @ 10m

2,000 Hours lamp Lifetime (May vary depending on different factors)

FUNCTION

2-45° Angle, Super Bright Beam and wide Zoom

8-facet Circular rotating prism, can be rotated in two directions with variable speed

Independent Frost filter

13 colors + white, half-color effect, linear color change and two-way variable speed rotation rainbow effect

Two Gobo wheels:

12 fixed Gobo+open, two directions shaking, animation, water effects

9 rotating glass gobo wheel

0-100% Linear Dimming

Advanced Optical system and Cooling System

Motorized Focus

Three-phase motors

High Speed Mechanical Shutter and Strobe

Precise movement, 540° Pan, 270° Tilit

CONTROL & CONNECTIONS

(1) DMX Channel Modes (18 channels)

Intelligent LCD Display

IP65 3pin DMX In/Out

IP65 powerCON Power In

DMX512, Auto run, Sound, Master/Slave

THERMAL & ELECTRICAL

700W max Power Consumption

Input voltage: 100-240V AC/50-60 Hz

APPROVALS / RATINGS

CE | RoHs Compliant | IP65

Light SIZE / WEIGHT

20.1" (510mm) Length

17.3" (440mm) Width

26.8" (680mm) Height

61.7 lbs (28 kg) net Weight

IV  Normal faulty and using attention

1) Normal faulty solution

There are professional parts like mainboard, power supply in lights. Non-professionals mustn’t disassemble item and parts without authorization.

1. Lamp is not on.

Possible reason：lamps don't cool down; lamps is out of  life. Solution is as following:

l The lamp doesn’t cool down because of improper operation. The lamp need 10 minutes to be cooling, and then you can restart it after this；

l Check if the lamp is out of life or not, change new lamp；

l Check the if there is electric leakage, off and poor contact between lamp and ignitor ；

l Change new ignitor.

2. Beam seems dim

Possible reason：service time of lamp is long or light patch is not clean, the solution is as following：

l Check if the lamp is out of life or not, change new lamp；

l Check if the optical part and lamp is clean or not. Please clean the lamp and other parts regularly.

3. Gobo is not clear

l Check if the channel value of focus is suitable the current projection distance or not.

4. Light works intermittently.

Possible reason：The internal wiring is in protection state. The solution is as following:

l Check if the fan works or is dirty；

l Check the switch of temperature control is on or off；

l Check if the lamp is out of life or not, change new lamp

5. The light can’t be controlled after reset.

Possible reason：problem signal line or the value of channel is wrong, the solution is as following:

l Check the initial address code and connection state of DMX signal line( the signal line is good or not, the XLR is loose or not)；

l Add signal amplifier, and 120 ohm terminal resistance；

6. Light can’t be started

Possible reason：power circuit is poor，solution is as following：

l Check if the fuse is broken or not, change new fuse；

l Check if there is the poor connection because of long transportation;

l Check the input power supply, mainboard and other parts.

2) Using attention

l Check if the local power is suitable for the rated voltage or not, leakage protector and over-current protector is suitable for the electrical load or not ；

l Don’t use the power line with damaged insulating layer, don’t connect the power line with other guide wire；

l Please clean the fans and parts every month. Otherwise the bad cooling system will cause some problem;

l In installation, the fixed screw must be fastening and there is must with safety rope with regular check；

l Easily flammable materials, e.g. decoration material and other surfaces and objects, must maintain a minimum distance of 3m to the housing! walls must maintain a minimum distance of 50cm to the housing! The device must be installed on a fireproof surface only (no carpet)! Always ensure a proper circulation of air;

l The continuous working hours should not be more than 10 hour and the interval time should be more than 10 minutes before restarting, otherwise the lamp will not be on because of over temperature protection;

l If you want the shutter for a long time, please use controller to close lamp;

l In order to make many lights follow scene effect, the light shouldn’t stay in unfinished scene for more than 3 minutes, then many lights can work on same step.

l Please stop it if there is abnormal during usage.