banner-products
You are here: Home » Products » Led Display » Profile Ellipsoidal Leko 200W quiet led studio light

Profile Ellipsoidal Leko 200W quiet led studio light

LED COB 200W Lekos

*LED COB 200W Lekos
*Interchangeable Lens Options (19°, 26°, 36°, 50°)
*Imported Japan Citizen COB LED
*High CRI≥93
*Extremely quiet fan, Copper tube heat Sinking, no any noise
*150W RGB LED Engine (COLORLED HD Profiles)
*200W, 3200k LED Engine (LED HD Tungsten)
*200W, 5600k LED (LED HD Daylight)
*200W, 3200k-5600k, Variable color temperature (VARLED HD)
Availability:
Quantity:
  • LED Profile HP
  • Prowalls
  • LED Screen 


Description

LED Profile Lekos ellipsoidal features a High PoweredLED COB 200W≥93 CRI 3200K/5600K LED engine producing 8,750lumens at full, 19°, 26°, 36°, and 50° interchangeable lens options (sold separately), (4) blade manual framing shutters, manual focus, DMX controlled electronic strobe, and variable dimming curve modes, adjustable refresh frequency and gamma brightness for flicker free operation for TV and FILM.


Features

*LED COB 200W Lekos

*Interchangeable Lens Options (19°, 26°, 36°, 50°)

*Imported Japan Citizen COB LED

*High CRI≥93

*Extremely quiet fan, Copper tube heat Sinking, no any noise

*150W RGB LED Engine (COLORLED HD Profiles)

*200W, 3200k LED Engine (LED HD Tungsten)

*200W, 5600k LED (LED HD Daylight)

*200W, 3200k-5600k, Variable color temperature (VARLED HD)



Specification


SOURCE

150W RGB LED Engine (COLORLED HD Profiles)

200W, 3200k LED Engine (LED HD Tungsten)

200W, 5600k LED (LED HD Daylight)

200W, 3200k-5600k, Variable color temperature (VARLED HD)

60,000 Hours LED Lifetime (May vary depending on different factors)


FUNCTION

LED COB 200W Lekos

Imported Japan Citizen COB LED

Interchangeable Lens Options* (19°, 26°, 36°, 50°)

High CRI≥93

Extremely quiet fan, Copper tube heat Sinking, no any noise

0-100% Linear dimming, Variable Dimming Curve Modes

Electronic Shutter/Strobe


CONTROL & CONNECTIONS

(2) DMX Channel Modes (1/2 channels)

Intelligent LCD Display

3-pin DMX In/Out

PowerCON Power In/Out

DMX512, Auto run, Sound, Master/Slave


THERMAL & ELECTRICAL 

220W max Power Consumption

Input voltage: 100-240V AC/50-60 Hz


APPROVALS / RATINGS

CE | RoHs Compliant | IP20


PACKAGE SIZE / WEIGHT

24.4" (620mm) Length

13" (330mm) Width

18.9" (480mm) Height

24.3lbs (11g) Weight


This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.


If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore it is essential that the device be earthed. The electric connection must carry out by qualified person. The device shall only be used with rate voltage and frequency. Make sure that the available voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don't project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.


Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving head together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors. Please refer to the diagram below. DMX-512 connection with DMX terminator


For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.

Previous: 
Next: 
Contact us

Your requirements, our pursuit

Quality, Innovation, Service, Honesty, Responsibility, Efficient, Patience, Diligence

Social Profiles

Leave a Message
Contact us

Quick Links

Contact Us

 (+86)-18102755163/(+86)-18620553640
 (+86)-18102755163

Stay In Touch

Copyright © 2021 PROWALLS ELECTRONICS CO LIMITED All Rights Reserved