Description
Outdoor Hybrid BWS380 is a powerful yet compact IP65-rated LED fixture offering outstanding BWS (Beam Wash Spot) qualities in any environment.
It is the ideal fixture for any outdoor or indoor application requiring superior output, bright and powerful Beams Wash Spot 3in1, and quiet operation, as well as stunningly precise gobos and colors. Outdoor Hybrid BWS380 provides the designer a comprehensive FX package with 14 colors and 12 fixed gobos & 9 rotating gobos, overlapping dual prisms, frost and 0-100% smooth dimming. Its indexable framing system provides full blackout shutter cuts for precise beam shape control.
Features
*IP65 rated waterproof Outdoor BWS moving head Light
*Osram R18 380W lamp
*2-45° Angle, sharpy Beam and wide Zoom
*Advanced Optical system and Cooling System
*Two Gobos wheels: fixed gobo wheel and rotating gobo wheel
*Rainbow effect
Specification
SOURCE
Osram R18 380W lamp
580,000 lux @ 10m
2,000 Hours lamp Lifetime (May vary depending on different factors)
FUNCTION
2-45° Angle, Super Bright Beam and wide Zoom
8-facet Circular rotating prism, can be rotated in two directions with variable speed
Independent Frost filter
13 colors + white, half-color effect, linear color change and two-way variable speed rotation rainbow effect
Two Gobo wheels:
12 fixed Gobo+open, two directions shaking, animation, water effects
9 rotating glass gobo wheel
0-100% Linear Dimming
Advanced Optical system and Cooling System
Motorized Focus
Three-phase motors
High Speed Mechanical Shutter and Strobe
Precise movement, 540° Pan, 270° Tilit
CONTROL & CONNECTIONS
(1) DMX Channel Modes (18 channels)
Intelligent LCD Display
IP65 3pin DMX In/Out
IP65 powerCON Power In
DMX512, Auto run, Sound, Master/Slave
THERMAL & ELECTRICAL
700W max Power Consumption
Input voltage: 100-240V AC/50-60 Hz
APPROVALS / RATINGS
CE | RoHs Compliant | IP65
Light SIZE / WEIGHT
20.1" (510mm) Length
17.3" (440mm) Width
26.8" (680mm) Height
61.7 lbs (28 kg) net Weight
I Notice and setup
l Keep dry, don’t use it in wet environment.
l Intermittent using can extend the life of item.
l Please often clean fan, fan net and lens to get better cooling and brightness effect.
l Please don’t clean the cover with solvent like alcohol.
To be on the safe side and under the terms of the security, do not allow to restructure and modify this product. Please note that because of man-made damage caused by improper use, is beyond the scope of our warranty.
This equipment pass strict inspection before shipment, please comply with the instruction manual operation requirements, to ensure the safe operation of the product under normal conditions. Any damage caused by improper operation, will cause the cessation of the warranty claim. Manufacturer does not accept any because of improper operation products or non-compliance of the instructions of any liability for property damage and personal injury.
Please place the manual in safe place for future reference and in products for sale or lease or handling running new holder.
l Do not operate when temperature up to 60°
l Make sure the equipment load-bearing structures can withstand the weight of more than 10 times when above ground installation.
l Only professional technique can repair this item to avoid the dangerous of electric shock.
l The power voltage difference can’t be more than 10% when the lamp works. Higher voltage can short the life of lamp and lower voltage can reduce the brightness.
l Cool down for 20 minutes before restart it again
l Please read this notice carefully before your operation.
RDM is an extended version of the DMX512-A protocol and is a remote device management (Remote Device Management) protocol. The traditional DMX512 protocol communication is a one-way communication. The protocol is based on the RS-485 bus, and RS-485 is a time-sharing multi-point, half-duplex protocol. Only one port is allowed to be output by the host at the same time, so pay attention to the following points when using RDM:
●Use a console or master device that supports RDM protocol;
●To use a bidirectional signal amplifier, the traditional unidirectional signal amplifier does not apply the RDM protocol, because the RMD protocol requires feedback data, and the use of a unidirectional signal amplifier will block the returned data, resulting in no search for fixtures;
●All fixtures must be set to DMX channel mode to ensure that there is only one master on the DMX cable
●A 120 ohm impedance matching resistor must be inserted between terminals 2 and 3 of the terminal plug. When the DMX cable is relatively long, reducing signal reflection will use differential signals to be more stable, which is beneficial to the quality of communication;
●When the fixtures are controlled by DMX but cannot be searched by RDM, first check the signal amplifier, and then check whether there is a bad contact between the 2 and 3 lines of the signal line