Description
Captain 19A is a high power 19x30W RGBW 4-IN-1 LEDs beam wash moving head light, Features include a fast 6° to 55° Sharp beam/ linear zoom system, a new Advanced collimator optic Lens produce prefect optical system and outstanding color macro effect, Wash is super bright and no shadow, Flicker free.
Features
*High power 19x30W RGBW 4-IN-1 LEDs
*Beam Wash 2-in-1
*Advanced collimator optic Lens
*6° - 55° Beam Angle and Zoom Range
*Three Pixel Ring Control and Color-Pixel Ring Macro Effects
*Flicker Free Operation for TV and FILM
*Adjustable Refresh Rate Frequency
Specification
SOURCE
High power 19x30W RGBW 4-IN-1 LEDs
60,000 Hours LED Lifetime (May vary depending on different factors)
FUNCTION
Beam Wash 2-in-1
Advanced collimator optic Lens
6° - 55° Beam Angle and Zoom Range
Three Pixel Ring Control and Color-Pixel Ring Macro Effects
Flicker Free Operation for TV and FILM
Adjustable Refresh Rate Frequency
0-100% linear dimming
Electronic Strobe
CONTROL & CONNECTIONS
(2) DMX Channel Modes (19/27 channels)
Intelligent LCD Menu Display
3pin/5pin DMX In/Out
PowerCON Power In/Out
DMX512, Auto run, Sound, Master/Slave
THERMAL & ELECTRICAL
600W max Power Consumption
Input voltage: 100-240V AC/50-60 Hz
APPROVALS / RATINGS
CE | RoHs Compliant | IP20
SIZE / WEIGHT
15.4" (390mm) Length
11.8" (300mm) Width
19.7" (500mm) Height
35.3 lbs (16 kg) Weight
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
y Unpack and check carefully there is no transportation damage before using the unit.
y Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
y It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
y The unit is for indoor use only. Use only in a dry location.
y The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
y Disconnect main power before replacement or servicing.
y Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
y Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its base.
y Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.
y In the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
y DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
y DO NOT open the unit within five minutes after switching off.
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people.
Light Sources: 19 x 30W 4in1 RGBW LED
Beam Angle: 6°~ 55°
Power Consumption: 600W
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 36*28*47 cm
Net Weight: 14.2 Kgs
Gross Weight: 16 Kgs
Control
DMX Channel: 19/27 Channel
Control Modes: DMX512/mater-Slave/Auto Run/Music
Pan/Tilt
Pan/Tilt: 540°/ 270°
Pan/Tilt Resolution: 8/16 bit
Construction
Display: 180°reversible LCD colorful Display
Data In/Out socket: 3-pin & 5-pin XLR sockets
Power Socket: Powercon in/out
Protection Rating: IP20
Features
Motorized liner zoom system, zoom range: 6°~55°
Outstanding color macro effect
Dimmer: 0~100% smooth dimming
Variable strobe effects
Fast, quiet operation and flicker free
Three section, led circle control
The DMX512 is widely used in intelligent lighting control,with a DMX 512 controller.connect several lights together,dmx in and dmx out,
3 pin XLR connectors: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address Code
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and Exit
1 | Address | Address 001～512 | Address setting 001-512 |
2 |
Run Mode | 1.DMX512 | Console control |
2.Auto | 1.Master | ||
2.Alone | |||
3.Sound | 1.Master | ||
2.Alone | |||
3 |
Reverse | 1.Pan Pan forward or reversed setting | 1.Yes |
2.No | |||
2.Tilt Tilt forward or reversed setting | 1.Yes | ||
2.No | |||
3.Display Display forward or reversed setting | 1.Yes | ||
2.No | |||
4 |
Channel |
27 channels |
27 channel mode |
19 channels |
19 channel mode | ||
5 |
Pan Degree | 540 | Pan angle 540°/360° Rotation |
360 | |||
6 | Mic sense | 001-100 | Sound sensitivity 001-100 |
7 | Inform | 1.CH Value | Each channel show CH value |
2.Temp ____℃ | Show the temperature of led board | ||
3.Soft V1.0 | Show the version number | ||
8 | Reset | 1.Yes |
Reset |
2.No | |||
9 | Default | 3.Yes | Factory setting |
4.No | |||
10 | Adjust | Pass word | **** |
1.Pan | Pan fine control | ||
2.Tilt | Tilt fine control | ||
3.Focus | Zoom fine control |
DMX channel´s functions and values (19/27DMX channels):
Mode/Channel | Value | Function | |
Standard | Zone | ||
1 | 1 | PAN Movement 8bit : | |
0-255 | Pan Movement | ||
2 | 2 | Pan Fine 16bit | |
0-255 | Fine control of Pan movement | ||
3 | 3 | TILT Movement 8bit : | |
0-255 | Tilt Movement | ||
4 | 4 | Tilt Fine 16bit | |
0-255 | Fine control of Tilt movement | ||
5 | 5 | Speed Pan/Tilt movement: | |
0-225 | max to min speed | ||
226-255 | no function | ||
6 | 6 | STROBE | |
0-255 | Strobe from slow to fast | ||
7 | 7 | Dimmer intensity: | |
0-255 | Intensity 0 to 100% | ||
8 | 8 | Dimmier mode | |
0-49 | Dimmer mode 1 | ||
50-99 | Dimmer mode 2 | ||
100-149 | Dimmer mode 3 | ||
150-255 | Dimmer mode 4 | ||
9 | 9 | Zoom : | |
0-255 | Zoom adjustment | ||
10 | Red LED -all arrays : | ||
0-255 | Red ( 0-Black , 255-100% Red ) | ||
11 | Green LED-all arrays : | ||
0-255 | Green ( 0-Black , 255-100% Green ) | ||
12 | Blue LED -all arrays : | ||
0-255 | Blue ( 0-Black , 255-100% Blue ) | ||
13 | White LED -all arrays : | ||
0-255 | White ( 0-Black , 255-100% White ) | ||
10 | Red LED -array 1 : | ||
0-255 | Red ( 0-Black , 255-100% Red ) | ||
11 | Green LED-array 1 : | ||
0-255 | Green ( 0-Black , 255-100% Green ) | ||
12 | Blue LED -array 1 : | ||
0-255 | Blue ( 0-Black , 255-100% Blue ) | ||
13 | White LED -array 1 : | ||
0-255 | White ( 0-Black , 255-100% White ) | ||
14 | Red LED -array 2 : | ||
0-255 | Red ( 0-Black , 255-100% Red ) | ||
15 | Green LED-array 2 : | ||
0-255 | Green ( 0-Black , 255-100% Green ) | ||
16 | Blue LED -array 2 : | ||
0-255 | Blue ( 0-Black , 255-100% Blue ) | ||
17 | White LED -array 2 : | ||
0-255 | White ( 0-Black , 255-100% White ) | ||
18 | Red LED -array 3 : | ||
0-255 | Red ( 0-Black , 255-100% Red ) | ||
19 | Green LED-array 3 : | ||
0-255 | Green ( 0-Black , 255-100% Green ) | ||
20 | Blue LED -array 3 : | ||
0-255 | Blue ( 0-Black , 255-100% Blue ) | ||
21 | White LED -array 3: | ||
0-255 | White ( 0-Black , 255-100% White ) | ||
14 | 22 | Rainbow: | |
0-4 | No function | ||
5-29 | R | ||
30-54 | G | ||
55-79 | B | ||
80-104 | W | ||
105-129 | Rainbow colours 1 | ||
130-154 | Rainbow colours 2 | ||
155-174 | Rainbow colours 3 | ||
175-179 | Rainbow colours 4 | ||
180-184 | Rainbow colours 5 | ||
185-189 | Rainbow colours 6 | ||
190-210 | Rainbow colours 7 | ||
211-255 | Crossfading colours from slow to fast | ||
15 | 23 | Color Presets: | |
0-4 | No function | ||
5--9 | White1 | ||
10--14 | White2 | ||
15-19 | White3 | ||
20-24 | White4 | ||
25-29 | White5 | ||
30-34 | White6 | ||
35-39 | Red | ||
40-44 | Green | ||
45-49 | Blue | ||
50-54 | Natural White | ||
55-59 | Full White | ||
60-64 | Yellow | ||
65-69 | Magenta | ||
70-74 | Cyan | ||
75-79 | Salmon | ||
80-84 | Turquoise | ||
85-89 | Light Green | ||
90-94 | Steel Blue | ||
95-99 | Orange | ||
100-104 | Straw | ||
105-109 | Pale Lavander | ||
110-114 | Pink | ||
115-119 | RED/WHITE | ||
120-124 | GREEN/RED | ||
125-129 | BLUE/GREEN | ||
130-134 | WHITE/RED | ||
135-139 | GREEN/PINK | ||
140-144 | RED/TURQUOISE | ||
145-149 | RED/WHITE/BLUE | ||
150-255 | Reserved | ||
16 | 24 | Chase Patterns: | |
1--14 | Led trun off | ||
15-30 | Chase 1 | ||
31-46 | Chase 2 | ||
47-62 | Chase 3 | ||
63-78 | Chase 4 | ||
79-94 | Chase 5 | ||
95-110 | Chase 6 | ||
111-126 | Chase 7 | ||
127-142 | Chase 8 | ||
143-158 | Chase 9 | ||
159-174 | Chase 10 | ||
175-190 | Chase 11 | ||
191-206 | Chase 12 | ||
207-222 | Chase 13 | ||
223-238 | Chase 14 | ||
239-255 | Chase 15 | ||
17 | 25 | Chase Speed: | |
0-125 | Fast to Slow Backward | ||
126-130 | Stop(Speed=0) | ||
131-255 | Slow to Fast Forward | ||
18 | 26 | Chase Fade: | |
0-255 | Fade Chase | ||
19 | 27 | Lamp on/off, reset, internal programs: | |
0-79 | Normal | ||
80-99 | All motor reset | ||
100-255 | Normal | ||
Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on
PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
C. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Ÿ Clean with soft cloth using normal glass cleaning fluid.
Ÿ Always dry the parts carefully.
Ÿ Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.